View EL2250C_878971.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

EL2250C, EL2450C
EL2250C, EL2450C
125MHz Single Supply Dual/Quad Op Amps
Features
* Specified for +3V, +5V, or 5V applications * Large input common mode range 0V < VCM < VS -1.2V * Output swings to ground without saturating * -3dB bandwidth = 125MHz * 0.1dB bandwidth = 30MHz * Low supply current = 5mA (per amplifier) * Slew rate = 275V/s * Low offset voltage = 4mV max * Output current = 100mA * High open loop gain = 80dB * Differential gain = 0.05% * Differential phase = 0.05
General Description
The EL2250C/EL2450C are part of a family of the electronics industries fastest single supply op amps available. Prior single supply op amps have generally been limited to bandwidths and slew rates to that of the EL2250C/EL2450C. The 125MHz bandwidth, 275V/s slew rate, and 0.05%/0.05 differential gain/differential phase makes this part ideal for single or dual supply video speed applications. With its voltage feedback architecture, this amplifier can accept reactive feedback networks, allowing them to be used in analog filtering applications. The inputs can sense signals below the bottom supply rail and as high as 1.2V below the top rail. Connecting the load resistor to ground and operating from a single supply, the outputs swing completely to ground without saturating. The outputs can also drive to within 1.2V of the top rail. The EL2250C/EL2450C will output 100mA and will operate with single supply voltages as low as 2.7V, making them ideal for portable, low power applications. The EL2250C/EL2450C are available in PDIP and SO packages in industry standard pin outs. Both parts operate over the industrial temperature range of -40C to +85C, and are part of a family of single supply op amps. For single amplifier applications, see the EL2150C/EL2157C. For dual and triple amplifiers with power down and output voltage clamps, see the EL2257C/EL2357C.
Applications
* * * * * * * * * Video amplifiers PCMCIA applications A/D drivers Line drivers Portable computers High speed communications RGB printers, FAX, scanners Broadcast equipment Active filtering
Connection Diagrams
OUTA 1 INA- 2 INA+ 3
Outline # MDP0031 MDP0027 MDP0027 MDP0027 MDP0031 MDP0027 MDP0027 MDP0027
14 OUTD A D 13 IND12 IND+ 11 GND 10 INC+ B + + C -
-
+
+
-
Ordering Information
Part No EL2250CN EL2250CS EL2250CS-T7 EL2250CS-T13 EL2450CN EL2450CS EL2450CS-T7 EL2450CS-T13 Package 8-Pin PDIP 8-Pin SO 8-Pin SO 8-Pin SO 14-Pin PDIP 14-Pin SO 14-Pin SO 14-Pin SO Tape & Reel 7" 13" 7" 13"
OUTA 1 INA- 2 INA+ 3 GND 4 B + EL2250C (8-Pin SO & 8-Pin PDIP) A +
8 VS+ 7 OUTB 6 INB5 INB+
VS+ 4 INB+ 5 INB- 6 OUTB 7
September 26, 2001
9 INC8 OUTC
EL2450C (14-Pin SO & 14-Pin PDIP)
Note: All information contained in this data sheet has been carefully checked and is believed to be accurate as of the date of publication; however, this data sheet cannot be a "controlled document". Current revisions, if any, to these specifications are maintained at the factory and are available upon your request. We recommend checking the revision level before finalization of your design documentation.
(c) 2001 Elantec Semiconductor, Inc.
EL2250C, EL2450C
EL2250C, EL2450C
125MHz Single Supply Dual/Quad Op Amps
Absolute Maximum Ratings (T
Supply Voltage between VS and GND Input Voltage (IN+, IN-) Differential Input Voltage Maximum Output Current Output Short Circuit Duration
A
= 25C)
+12.6V GND-0.3V,VS+0.3V 6V 90mA (Note 1)
Power Dissipation Storage Temperature Range Ambient Operating Temperature Range Operating Junction Temperature
See Curves -65C to +150C -40C to +85C 150C
Important Note: All parameters having Min/Max specifications are guaranteed. Typ values are for information purposes only. Unless otherwise noted, all tests are at the specified temperature and are pulsed tests, therefore: TJ = TC = TA.
DC Electrical Characteristics
VS = +5V, GND = 0V, TA = 25C, VCM = 1.5V, VOUT = 1.5V, unless otherwise specified. Parameter VOS TCVOS IB IOS TCIOS PSRR CMRR CMIR RIN CIN ROUT IS PSOR Offset Voltage Offset Voltage Temperature Coefficient Input Bias Current Input Offset Current Input Bias Current Temperature Coefficient Power Supply Rejection Ratio Common Mode Rejection Ratio Common Mode Input Range Input Resistance Input Capacitance Output Resistance Supply Current (per amplifier) Power Supply Operating Range Common Mode SO Package PDIP Package AV = +1 VS = +12V 2.7 Description EL2250C EL2450C Measured from TMIN to TMAX VIN = 0V VIN = 0V Measured from TMIN to TMAX VS = +2.7V to +12V VCM = 0V to +3.8V VCM = 0V to +3.0V 55 55 55 0 1 2 1 1.5 40 5 6.5 12.0 -750 Test Conditions Min -2 -4 10 -5.5 150 50 70 65 70 VS-1.2 -10 750 Typ Max 2 4 Unit mV mV V/C A nA nA/C dB dB dB V M pF pF m mA V
DC Electrical Characteristics
VS = +5V, GND = 0V, TA = 25C, VCM = +1.5V, VOUT = +1.5V, unless otherwise specified. Parameter AVOL Open Loop Gain Description Test Conditions VS = +12V, V OUT = +2V to +9V, RL = 1k to GND VOUT = +1.5V to +3.5V, RL = 1k to GND VOUT = +1.5V to +3.5V, RL = 150 to GND VOP Positive Output Voltage Swing VS = +12V, AV = +1, RL = 1k to 0V VS = +12V, AV = +1, RL = 150 to 0V VS = 5V, AV = +1, RL = 1k to 0V VS = 5V, AV = +1, RL = 150 to 0V VS = +3V, AV = +1, RL = 150 to 0V 3.4 1.8 9.6 Min 60 Typ 80 70 60 10.8 10.0 4.0 3.8 1.95 Max Unit dB dB dB V V V V V
2
EL2250C, EL2450C
EL2250C, EL2450C
125MHz Single Supply Dual/Quad Op Amps
DC Electrical Characteristics
VS = +5V, GND = 0V, TA = 25C, VCM = +1.5V, VOUT = +1.5V, unless otherwise specified. Parameter VON Negative Output Voltage Swing Output Current [1] Description Test Conditions VS = +12V, AV = +1, RL = 150 to 0V V S= 5V, AV = +1, RL = 1k to 0V VS = 5V, AV = +1, RL = 150 to 0V IOUT VS = 5V, AV = +1, RL = 10 to 0V VS = 5V, AV = +1, RL = 50 to 0V60V mA 1. Internal short circuit protection circuitry has been built into the EL2250C/EL2450C; see the Applications section 75 Min Typ 5.5 -4.0 -3.7 100 -3.4 Max 8 Unit mV V V mA
Closed Loop AC Electrical Characteristics
VS = +5V, GND = 0V, TA = 25C, VCM = +1.5V, VOUT = +1.5V, AV = +1, R F = 0, RL = 150 to GND pin, unless otherwise specified. [1] Parameter BW Description -3dB Bandwidth (VOUT=400mVp-p) Test Conditions VS = +5V, AV = +1, RF = 0 VS = +5V, AV = -1, RF = 500 VS = +5V, AV = +2, RF = 500 VS = +5V, AV = +10, RF = 500 VS = +12V, AV = +1, RF = 0 VS = +3V, AV = +1, RF = 0 BW 0.1dB Bandwidth (VOUT=400mVp-p) Gain Bandwidth Product Phase Margin Slew Rate Rise Time, Fall Time Overshoot Propagation Delay 0.1% Settling Time 0.01% Settling Time dG dP eN iN Differential Gain [2] Differential Phase [2] Input Noise Voltage Input Noise Current VS = +12V, AV = +1, RF = 0 VS = +5V, AV = +1, RF = 0 VS = +3V, AV = +1, RF = 0 GBWP PM SR tR, tF OS tPD tS VS = +12V, @ AV = +10 RL = 1k, CL = 6pF VS = +10V, RL = 150, VOUT = 0V to +6V VS = +5V, RL = 150, VOUT = 0V to +3V 0.1V Step 0.1V Step 0.1V Step VS = 5V, RL = 500, AV = +1, V OUT = 3V VS = 5V, RL = 500, AV = +1, V OUT = 3V AV = +2, RF = 1k AV = +2, RF = 1k f = 10kHz f = 10kHz 200 Min Typ 125 60 60 6 150 100 25 30 20 60 55 275 300 2.8 10 3.2 40 75 0.05 0.05 48 1.25 Max Unit MHz MHz MHz MHz MHz MHz MHz MHz MHz MHz V/s V/s ns % ns ns ns % nV/Hz pA/Hz
1. All AC tests are performed on a "warmed up" part, except slew rate, which is pulse tested 2. Standard NTSC signal = 286mVP-P, f = 3.58MHz, as V IN is swept from 0.6V to 1.314V; RL is DC coupled
3
EL2250C, EL2450C
EL2250C, EL2450C
125MHz Single Supply Dual/Quad Op Amps
Typical Performance Curves
Non-Inverting Frequency Response (Gain) Non-Inverting Frequency Response (Phase) 3dB Bandwidth vs Temperature for NonInverting Gains
Inverting Frequency Response (Gain)
Inverting Frequency Response (Phase)
3dB Bandwidth vs Temperature for Inverting Gains
Frequency Response for Various RL
Frequency Response for Various C L
Non-Inverting Frequency Response vs Common Mode Voltage
4
EL2250C, EL2450C
EL2250C, EL2450C
125MHz Single Supply Dual/Quad Op Amps
3dB Bandwidth vs Supply Voltage for Non-Inverting Gains
Frequency Response for Various Supply Voltages, AV = + 1
PSSR and CMRR vs Frequency
3dB Bandwidth vs Supply Voltage for Inverting Gains
Frequency Response for Various Supply Voltages, AV = + 2
PSRR and CMRR vs Die Temperature
Open Loop Gain and Phase vs Frequency
Open Loop Voltage Gain vs Die Temperature
Closed Loop Output Impedance vs Frequency
5
EL2250C, EL2450C
EL2250C, EL2450C
125MHz Single Supply Dual/Quad Op Amps
Large Signal Step Response, VS = +3V
Large Signal Step Response, V S = +5V
Large Signal Step Response, VS = +12V
Small Signal Step Response
Large Signal Step Response, VS = 5V
Slew Rate vs Temperature
Settling Time vs Settling Accuracy
Voltage and Current Noise vs Frequency
6
EL2250C, EL2450C
EL2250C, EL2450C
125MHz Single Supply Dual/Quad Op Amps
Differential Gain for Single Supply Operation
Differential Phase for Single Supply Operation
Differential Gain and Phase for Dual Supply Operation
2nd and 3rd Harmonic Distortion vs Frequency
2nd and 3rd Harmonic Distortion vs Frequency
2nd and 3rd Harmonic Distortion vs Frequency
Output Voltage Swing vs Frequency for THD < 0.1%
Output Voltage Swing vs Frequency for Unlimited Distortion
Output Current vs Die Temperature
7
EL2250C, EL2450C
EL2250C, EL2450C
125MHz Single Supply Dual/Quad Op Amps
Supply Current vs Supply Voltage (per amplifier)
Supply Current vs Die Temperature (per amplifier)
Input Resistance vs Die Temperature
Offset Voltage vs Die Temperature (4 Samples)
Input Bias Current vs Input Voltage
Input Offset Current and Input Bias Current vs Die Temperature
Positive Output Voltage Swing vs Die Temperature, RL = 150 to GND
Negative Output Voltage Swing vs Die Temperature, RL = 150 to GND
Channel to Channel Isolation vs Frequency
8
EL2250C, EL2450C
EL2250C, EL2450C
125MHz Single Supply Dual/Quad Op Amps
1.8 1.6 1.4 Power Dissipation (W) 1.2 1 0.8 0.6 0.4 0.2 0
Package Power Dissipation vs Ambient Temp. SEMI G42-88 Single Layer Test Board 1.54W 1.25W
PD IP 14
PD IP8
1.2 1 Power Dissipation (W)
Package Power Dissipation vs Ambient Temp. JEDEC JESD51-3 Low Effective Thermal Conductivity Test Board 1.042W
SO 14
J
A=
81
C /W
0.8 0.6 0.4 0.2 0
781W
JA =
12
JA = 1
00 C
SO 8
0 C/ W
JA=
/W
16 0C
/W
0
25
50
75 85
100
125
150
0
25
50
75 85
100
125
150
Ambient Temperature (C)
Ambient Temperature (C)
Simplified Schematic
9
EL2250C, EL2450C
EL2250C, EL2450C
125MHz Single Supply Dual/Quad Op Amps
Applications Information
Product Description
The EL2250C/EL2450C are part of a family of the industries fastest single supply operational amplifiers. Connected in voltage follower mode, their -3dB bandwidth is 125MHz while maintaining a 275 V/s slew rate. With an input and output common mode range that includes ground, these amplifiers were optimized for single supply operation, but will also accept dual supplies. They operate on a total supply voltage range as low as +2.7V or up to +12V. This makes them ideal for +3V applications, especially portable computers. While many amplifiers claim to operate on a single supply, and some can sense ground at their inputs, most fail to truly drive their outputs to ground. If they do succeed in driving to ground, the amplifier often saturates, causing distortion and recovery delays. However, special circuitry built into the EL2250C/EL2450C allows the output to follow the input signal to ground without recovery delays.
Supply Voltage Range and Single-Supply Operation
The EL2250C/EL2450C have been designed to operate with supply voltages having a span of greater than 2.7V, and less than 12V. In practical terms, this means that the EL2250C/EL2450C will operate on dual supplies ranging from 1.35V to 6V. With a single-supply, the EL2250C/EL2450C will operate from +2.7V to +12V. Performance has been optimized for a single +5V supply. Pins 8 and 4 are the power supply pins on the EL2250C. The positive power supply is connected to pin 8. When used in single supply mode, pin 4 is connected to ground. When used in dual supply mode, the negative power supply is connected to pin 4. Pins 4 and 11 are the power supply pins on the EL2450C. The positive power supply is connected to pin 4. When used in single supply mode, pin 11 is connected to ground. When used in dual supply mode, the negative power supply is connected to pin 11. As supply voltages continue to decrease, it becomes necessary to provide input and output voltage ranges that can get as close as possible to the supply voltages. The EL2250C/EL2450C have an input voltage range that includes the negative supply and extends to within 1.2V of the positive supply. So, for example, on a single +5V supply, the EL2250C/EL2450C have an input range which spans from 0V to 3.8V. The output range of the EL2250C/EL2450C is also quite large. It includes the negative rail, and extends to within 1V of the top supply rail with a 1k load. On a +5V supply, the output is therefore capable of swinging from 0V to +4V. On split supplies, the output will swing 4V. If the load resistor is tied to the negative rail and split supplies are used, the output range is extended to the negative rail.
Power Supply Bypassing And Printed Circuit Board Layout
As with any high-frequency device, good printed circuit board layout is necessary for optimum performance. Ground plane construction is highly recommended. Lead lengths should be as short as possible. The power supply pins must be well bypassed to reduce the risk of oscillation. The combination of a 4.7F tantalum capacitor in parallel with a 0.1 F ceramic capacitor has been shown to work well when placed at each supply pin. For single supply operation, where the GND pin is connected to the ground plane, a single 4.7F tantalum capacitor in parallel with a 0.1F ceramic capacitor across the VS+ and GND pins will suffice. For good AC performance, parasitic capacitance should be kept to a minimum. Ground plane construction should be used. Carbon or Metal-Film resistors are acceptable with the Metal-Film resistors giving slightly less peaking and bandwidth because of their additional series inductance. Use of sockets, particularly for the SO package should be avoided if possible. Sockets add parasitic inductance and capacitance which will result in some additional peaking and overshoot.
10
Choice Of Feedback Resistor, RF
The feedback resistor forms a pole with the input capacitance. As this pole becomes larger, phase margin is reduced. This increases ringing in the time domain and peaking in the frequency domain. Therefore, RF has
EL2250C, EL2450C
EL2250C, EL2450C
125MHz Single Supply Dual/Quad Op Amps
some maximum value which should not be exceeded for optimum performance. If a large value of RF must be used, a small capacitor in the few picofarad range in parallel with RF can help to reduce this ringing and peaking at the expense of reducing the bandwidth. As far as the output stage of the amplifier is concerned, RF + RG appear in parallel with RL for gains other than +1. As this combination gets smaller, the bandwidth falls off. Consequently, RF has a minimum value that should not be exceeded for optimum performance. For AV = +1, RF = 0 is optimum. For AV = -1 or +2 (noise gain of 2), optimum response is obtained with RF between 500 and 1k. For Av = -4 or +5 (noise gain of 5), keep RF between 2k and 10k. current approaches zero, the NPN turns off, and dG and dP will increase. This becomes more critical as the load resistor is increased in value. While driving a light load, such as 1k, if the input black level is kept above 1.25V, dG and dP are a respectable 0.03% and 0.03. For other biasing conditions see the Differential Gain and Differential Phase vs. Input Voltage curves.
Output Drive Capability
In spite of their moderately low 5mA of supply current, the EL2250C/EL2450C are capable of providing 100mA of output current into a 10 load, or 60mA into 50. With this large output current capability, a 50 load can be driven to 3V with VS = 5V, making it an excellent choice for driving isolation transformers in telecommunications applications.
Video Performance
For good video performance, an amplifier is required to maintain the same output impedance and the same frequency response as DC levels are changed at the output. This can be difficult when driving a standard video load of 150, because of the change in output current with DC level. Differential Gain and Differential Phase for the EL2250C/EL2450C are specified with the black level of the output video signal set to +1.2V. This allows ample room for the sync pulse even in a gain of +2 configuration. This results in dG and dP specifications of 0.05% and 0.05 while driving 150 at a gain of +2. Setting the black level to other values, although acceptable, will compromise peak performance. For example, looking at the single supply dG and dP curves for RL =150, if the output black level clamp is reduced from 1.2V to 0.6V dG/dP will increase from 0.05%/0.05 to 0.08%/0.25 Note that in a gain of +2 configuration, this is the lowest black level allowed such that the sync tip doesn't go below 0V. If your application requires that the output goes to ground, then the output stage of the EL2250C/EL2450C, like all other single supply op amps, requires an external pull down resistor tied to ground. As mentioned above, the current flowing through this resistor becomes the DC bias current for the output stage NPN transistor. As this
Driving Cables and Capacitive Loads
When used as a cable driver, double termination is always recommended for reflection-free performance. For those applications, the back-termination series resistor will de-couple the EL2250C/EL2450C from the cable and allow extensive capacitive drive. However, other applications may have high capacitive loads without a back-termination resistor. In these applications, a small series resistor (usually between 5 and 50 ) can be placed in series with the output to eliminate most peaking. The gain resistor (RG) can then be chosen to make up for any gain loss which may be created by this additional resistor at the output.
Video Sync Pulse Remover Application
All CMOS Analog to Digital Converters (A/Ds) have a parasitic latch-up problem when subjected to negative input voltage levels. Since the sync tip contains no useful video information and it is a negative going pulse, we can chop it off. Figure 1 shows a unity gain connected amplifier A of an EL2250C. Figure 2 shows the complete input video signal applied at the input, as well as the output signal with the negative going sync pulse removed.
11
EL2250C, EL2450C
EL2250C, EL2450C
125MHz Single Supply Dual/Quad Op Amps
conditions, or package type need to be modified for the EL2250C/EL2450C to remain in the safe operating area. The maximum power dissipation allowed in a package is determined according to [1]:
T JMAX - T AMAX PD MAX = -------------------------------------------J A
where: TJMAX = Maximum Junction Temperature
Figure 1.
TAMAX = Maximum Ambient Temperature JA = Thermal Resistance of the Package PDMAX = Maximum Power Dissipation in the Package. The maximum power dissipation actually produced by an IC is the total quiescent supply current times the total power supply voltage, plus the power in the IC due to the load, or [2]
V OUT PDMAX = N x V s x I SMAX + ( V S - V OUT ) x --------------- RL
Figure 2. Short Circuit Current Limit
The EL2250C/EL2450C have internal short circuit protection circuitry that protect it in the event of its output being shorted to either supply rail. This limit is set to around 100mA nominally and reduces with increasing junction temperature. It is intended to handle temporary shorts. If an output is shorted indefinitely, the power dissipation could easily increase such that the part will be destroyed. Maximum reliability is maintained if the output current never exceeds 90mA. A heat sink may be required to keep the junction temperature below absolute maximum when an output is shorted indefinitely. where: N = Number of amplifiers VS = Total Supply Voltage ISMAX = Maximum Supply Current per amplifier VOUT = Maximum Output Voltage of the Application RL = Load Resistance tied to Ground If we set the two PDMAX equations, [1] & [2], equal to each other, and solve for VS, we can get a family of curves for various loads and output voltages according to [3]:
R L x ( T JMAX - T AMAX ) --------------------------------------------------------------- + ( V O U T ) N x JA V S = -----------------------------------------------------------------------------------------( IS x R L ) + V OUT
Power Dissipation
With the high output drive capability of the EL2250C/EL2450C, it is possible to exceed the 150C Absolute Maximum junction temperature under certain load current conditions. Therefore, it is important to calculate the maximum junction temperature for the application to determine if power-supply voltages, load
12
EL2250C, EL2450C
EL2250C, EL2450C
125MHz Single Supply Dual/Quad Op Amps
Figures 3 through 6 below show total single supply voltage VS vs. RL for various output voltage swings for the PDIP and SO packages. The curves assume WORST CASE conditions of TA = +85C and IS = 6.5mA per amplifier.
13
EL2250C, EL2450C
EL2250C, EL2450C
125MHz Single Supply Dual/Quad Op Amps
EL2250C Single Supply Voltage vs R LOAD for Various VOUT (PDIP Package)
EL2450C Single Supply Voltage vs R LOAD for Various VOUT (PDIP Package)
Figure 3.
Figure 5.
EL2250C Single Supply Voltage vs R LOAD for Various VOUT (SO Package)
EL2450C Single Supply Voltage vs R LOAD for Various VOUT (SO Package)
Figure 4. Figure 6.
14
EL2250C, EL2450C
EL2250C, EL2450C
125MHz Single Supply Dual/Quad Op Amps
EL2250C/EL2450C Macromodel (one amplifier)
* Revision A, April 1996 * Pin numbers reflect a standard single op amp. * Connections: +input * | -input * | | +Vsupply * ||| -Vsupply * | | | | output .subckt EL2250/el 3 2 7 4 6 * * Input Stage * i1 7 10 250A i2 7 11 250A r1 10 11 4k q1 12 2 10 qp q2 13 3 11 qpa r2 12 4 100 r3 13 4 100 * * Second Stage & Compensation * gm 15 4 13 12 4.6m r4 15 4 15Meg c1 15 4 0.36pF * * Poles * e1 17 4 15 4 1.0 r6 17 25 400 c3 25 4 1pF r7 25 18 500 c4 18 4 1pF * * Output Stage * i3 20 4 1.0mA q3 7 23 20 qn q4 7 18 19 qn q5 7 18 21 qn q6 4 20 22 qp q7 7 23 18 qn d1 19 20 da r8 21 6 2 r9 22 6 2 r10 18 21 10k r11 7 23 100k d2 23 24 da d3 24 4 da d4 23 18 da * * Power Supply Current * ips 7 4 3.2mA * * Models * .model qn npn(is=800e-18 bf=150 tf=0.02nS) .model qpa pnp(is=810e-18 bf=50 tf=0.02nS) .model qp pnp(is=800e-18 bf=54 tf=0.02nS) .model da d(tt=0nS)
.ends
15
EL2250C, EL2450C
EL2250C, EL2450C
125MHz Single Supply Dual/Quad Op Amps
EL2250C/EL2450C Macromodel (one amplifier)
16
EL2250C, EL2450C
EL2250C, EL2450C
125MHz Single Supply Dual/Quad Op Amps
General Disclaimer
Specifications contained in this data sheet are in effect as of the publication date shown. Elantec, Inc. reserves the right to make changes in the circuitry or specifications contained herein at any time without notice. Elantec, Inc. assumes no responsibility for the use of any circuits described herein and makes no representations that they are free from patent infringement.
WARNING - Life Support Policy
September 26, 2001
Elantec Semiconductor, Inc.
675 Trade Zone Blvd. Milpitas, CA 95035 Telephone: (408) 945-1323 (888) ELANTEC Fax: (408) 945-9305 European Office: +44-118-977-6020 Japan Technical Center: +81-45-682-5820
17
Elantec, Inc. products are not authorized for and should not be used within Life Support Systems without the specific written consent of Elantec, Inc. Life Support systems are equipment intended to support or sustain life and whose failure to perform when properly used in accordance with instructions provided can be reasonably expected to result in significant personal injury or death. Users contemplating application of Elantec, Inc. Products in Life Support Systems are requested to contact Elantec, Inc. factory headquarters to establish suitable terms & conditions for these applications. Elantec, Inc.'s warranty is limited to replacement of defective components and does not cover injury to persons or property or other consequential damages.
Printed in U.S.A.

▲Up To Search▲

Price & Availability of EL2250C

	To Download EL2250C Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .